As an illustration, we could use a pipe or tube to connect the high port and the low port of a differential pressure transmitter. After that, we could simultaneously expose both ports to a source of fluid pressure, like the pressurized air produced by an air compressor. This would be one way to use a differential pressure transmitter. This will show us how to connect the high port of differential pressure transmitter price to the low port of the same device. Our ability to measure the pressure differential will be facilitated as a result of this. Even if we change the total amount of static pressure that is being applied to both ports, the transmitter should still indicate that there is not a differential pressure that is being applied. This is because there is no difference in the amount of pressure that is being applied to each port. If there aren't any problems with the functionality of it, then this is the case.
The sensing diaphragm of the transmitter shouldn't feel any net force pushing it to the left or right as long as the pressures that are being applied to each port are equivalent. As long as the pressures that are being applied to each port are equivalent, the sensing diaphragm of the transmitter should not feel any force pushing it to the left or right. The force that is exerted on the diaphragm by the fluid pressure coming from the high port should be precisely balanced out (cancelled) by the force that is exerted on the diaphragm by the fluid pressure coming from the low port. This will ensure that the diaphragm remains in a state of equilibrium. By doing so, the equilibrium of the diaphragm will be maintained throughout the process.
The process of connecting the red and block test leads of a voltmeter to the same point in an electrical circuit and then adjusting the amount of voltage that is being applied between that point and the earth ground is an example of an analogy that can be derived from the field of electricity. This process is an illustration of an analogy that can be derived from the field of electricity. This procedure exemplifies how one can derive an analogy from the subject of electricity. Voltmeters only register differences in potential between the voltmeter's test leads, and because those test leads are now electrically common to one another, the magnitude of the common-mode voltage that exists between that one point of the circuit and earth ground is irrelevant from the perspective of the voltmeter. Voltmeters only register differences in potential between the voltmeter's test leads. Voltmeters are designed to detect only differences in potential that exist between the test leads of the voltmeter.
The value of the common mode is never registered by the differential measurement device; rather, it only registers the amount of difference (zero) that exists between its sensing points. In other words, the differential measurement device never registers the value of the common mode.
The same fundamental concept, which is referred to as common-mode rejection, can be seen to be at work in circuits that are more complicated in terms of their fluids or electricity.
Take into consideration the following scenario involving a differential power transmitter, also known as a DP transmitter, and a voltmeter, both of which are instruments that are used to measure differential quantities in a circuit known as a divider:
Because it only responds to the difference between the two measurement points, the differential measurement device disregards the common-mode value of 97.5 PSI for the pressure transmitter and 97.5 volts for the voltmeter. This is because it only responds to the difference between the two measurement points. Because it only responds to the difference between the two measurement points, the differential measurement device gives this result.
In this particular illustration, the high side of each measuring instrument is connected to the point of lesser value. As a consequence of this connection, the difference that is being measured is a quantity that has a negative value. This is done solely with the intention of creating a more exciting scenario for the audience to experience.
In the same way that digital voltmeters can measure electrical potential differences, modern differential pressure (DP) transmitters are able to accurately measure pressure differences in both positive and negative directions. This capability extends to pressure differences in either the positive or negative directions, depending on which one is being measured.
The following information regarding pressure ratings can be found displayed on the nameplate of a Foxboro model 13A differential pressure transmitter price. When it comes to differential pressure instruments, these pressure ratings offer a striking illustration of the differences between differential pressure and common-mode pressure:
According to the engraved information on this nameplate, the transmitter has a calibrated differential pressure range that is equal to fifty inches of water column. Because 1.8 pounds per square inch is approximately equivalent to fifty inches of water column, this range of the transmitter's differential pressure is quite precise.
On the other hand, the nameplate indicates that the transmitter has the capacity to withstand a maximum working pressure (MWP) of 1500 pounds per square inch. This indicates that the transmitter can work effectively under very high pressures. The term "working pressure" refers to the amount of gauge pressure that is dispersed uniformly across all of the ports in the system. This is not making a reference to the difference in pressure that exists between the ports.
If we take these numbers at their face value, it indicates that this transmitter will report a reading of zero (there will be no differential pressure), even if the gauge pressure that is applied equally to both ports is a full 1500 PSI! To put this another way, the differential pressure transmitter will not respond to the common-mode gauge pressure of up to 1500 PSI. Instead, it will only react to extremely minute pressure differences between the ports (a differential pressure of 1.8 PSI will be sufficient to stimulate the transmitter to full scale output).
Comments (0)